Worx-tools WU601.1 User Manual download pdf (Page 13)

Router ENG

router.

• Insert the guide rods (C) into router base. For

maximum stability, make sure each rod goes

through both holes and protrudes out the other

side of the router base (At a maximum, the rods

must be inserted far enough into the router

base that they are supported from below base.

• Securely fasten the router to the rods by

tightening the locking screws (12). The largest

circles and arcs can be made when the guide

rods enter the side of the router where the

locking screws (12) are located.

• Mark the workpiece at the center of the desired

circle.

• Using the centering slots on the edge of the

pivot plate (22), center the pivot plate on the

center mark and attach to the workpiece with

several strips of strong tape placed over the

pivot plate in a crisscross pattern.

• Place ﬁne adjustment guide (F) on pivot plate

(22) so the hole in ﬁne adjustment guide (F) ﬁts

over the steel pin.

• Adjust the position of the rods and router as

necessary to achieve the desired radius of the

circle or arc, then securely tighten wing knobs.

13. CARBON BRUSH REPLACEMENT

Always be sure that the tool is switched off

and unplugged before attempting to perform

inspection or maintenance.

There are 2 motor brushes which can be easily

accessed on either the front or back of the

motor housing.

ATTENTION:

When servicing a tool, ALWAYS use only

identical replacement parts.

STEP 1: Locate the plastic motor brush caps on

both the front and back of the motor housing.

STEP 2: Remove the threaded access cap on

accessible carbon brushes (30) with a ﬂathead

screwdriver and turn the screw in a counter-

clockwise rotation to loosen.

STEP 3: Gently remove the old motor brush.

STEP 4: Carefully insert the replacement brush.

Ensure the brush is completely inserted into

the holder and is seated properly and is free to

move inside its holder.

STEP 5: Replace the access cap with the ﬂat-

head screwdriver, turning clockwise to tighten.

Do not apply excessive force as this may

damage the access plug.

Note: Always change both sets of brushes at

the same time.

MAINTENANCE

Your power tool requires no additional

lubrication or maintenance. There are no user

serviceable parts in your power tool. Never

use water or chemical cleaners to clean your

power tool. Wipe clean with a dry cloth. Always

store your power tool in a dry place. Keep the

motor ventilation slots clean. Keep all working

controls free of dust. If you see some sparks

ﬂashing in the ventilation slots, this is normal

and will not damage your power tool.

ENVIRONMENTAL

PROTECTION

Waste electrical products should not

be disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or retailer for

recycling advice.

WARRANTY STATEMENT

If your WORX product becomes defective due

to faulty materials or workmanship within the

speciﬁed warranty period of:

• 12 months from the date of purchase.

We guarantee to repair or replace all defective

parts free of charge, repair products subject

to fair wear and tear, free of charge, or at

our discretion,replace the unit free of charge

to ensure minimum inconvenience to the

customer. Your warranty is subject to the

following conditions:

• Proof of purchase date and a valid receipt is

produced.

• The product has not been misused.

• Unauthorized persons have not attempted

repairs.

• The product has not been used for hire

purposes.

• The product has not sustained damage

through foreign objects, substances or

accidents.

• Damage is not a result of ﬁtting non-approved

UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 13 2006-7-26 14:08:54

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 25 26

Comments to this Manuals

No comments

Worx-tools WU601.1 User Manual Page 13

Comments to this Manuals

Related products and manuals for Woodworking Worx-tools WU601.1